I mentioned I did a rebuild of my NFT test before leaving my system unattended, and as far as my attention goes, in the fore for four days.
Yeah I just wanted to say "fore for four" in a sentence.
It wasn't as fulfilling as you might think.
But this is what I did....
Or at least this is the exit tube I used to have.
The inlet tube was even smaller, at 4mm.
It was getting itself blocked on most days.
Now I add the entire flow of my pump through the NFT test. I guess it's not really NFT now because its no longer a film of water, but rather a tube half full of water.
I went with 12mm poly because I have a lot of it, and a lot of fittings lying around.
12mm polly is around the same diameter that exits my pump, so anything that can make it through my sad little pump should flow through the rest of the system without blockage.
At the time, I was also getting ready to go away for a few days, so didn't really have time to be fussy.
It would have been better to use straight fittings, and curve my pipes rather than have these right angle fittings as they slow the flow a bit, and I'm struggling with getting enough flow as it is.
There has been a few times where I found it expedient to employ what I like to call "Force tapping" a thread.
It involves screwing something into a place where there is not yet a thread for said something. Oddly enough, if you unscrew it, you will often see a shiny new thread.
It even works when both parts are plastic.
It also ruins the thread of the thing you are trying to screw in, so be careful how you employ this method.
Plumbing tape probably would have been better.
Actually, what would have been better, is whatever you would get is you went to the hardware and asked someone for a part that would do exactly what I'm doing. I'm guessing there is one.
I also mounted the entire thing onto some milk bottles full of water. This is an attempt to shed some of the heat that the PVC tube picks up on a hot day, and store that heat into the milk bottle heat sinks.
It should work a bit, but I'm not sure I'll need it any more because of the high rate of flow I'll be putting through the tube.
This is a bit deceiving because the water flows differently when the plants are in place, and it makes the other end dip a little.
The depth is now more like 25mm, where it was 5mm before.
It's very easy to check by lifting a pot out and seeing the water mark.
Due to the length of the tube, it now enters the grow bed from the far corner. This means it no longer dumps into the core tester.
There were no worms in the core sample I took last, and I'm wondering if having the water dump somewhere else might change that.
Today when I pulled up a lettuce, there was a worm within the root system, so they are in there.
[edit from the future - This turned out to leak a bit ]
Things so far...
Animation (5) Aquaponics (338) Bread (15) Cheese (14) cooking (49) electronics (57) Epic adventurer (20) Escargot (2) Fire (6) Fraudster (1) Handmade fishing lures (31) Home made preserves (11) Making smoked foods (11) Mold making (7) Movie watcher and critic (2) Photography (17) PVC (36) Snail farming (6) Solar hot water (26) Solar photovoltaic panels (7) Stirling Engines (11) Thinking (49) Vermiculture (1) Wind energy (25)
The bell siphon was a clever thing for someone to design, and as such you feel a bit of that "clever" rub off onto you when you m...
You see CHIFT PIST a lot in the aquaponics forums and it means "constant height in fish tank, pump in sump tank". And its a very g...
A "bell siphon" is a device that automates the flooding and draining of an aquaponics grow bed, even though the pump is adding wa...
Painting lures is easier if you don't know how. I don't, so I'm already well on my way. I started by owning a printer. That ...
A while ago I tried to make a fish fed fish feeder design that would allow the fish to feed themselves. I think It's made. I say &q...
Apparently, marron come in two varieties. Hairy and not so hairy. Cherax cainii (smooth) and Cherax tenuimanus, or Margret River marron (hai...
In aquaponics, one issue that can effect your success rate is the pH of your water. pH is a measure of water's (or soil's or whateve...
With a little practice its possible to make a screw. If you bend your wire into an eyelet, its possible to make a screw in eyelet. The use...
I had an idea, but now I'm not sure it was mine after all. But here it is anyway. I need to get solids out of the water for the NFT, ...
This post is a follow up to the " handmade fishing lures how to get most out of your printer " post describing my way to colour ha...