I like walking pace.
In fact walking pace is my favourite pace.
I've mentioned that before.
I like it so much, that what I really, really want to do is travel 2000km at it, on an epic adventure on a river. 2000km at 3kph should take roughly a very long time.
It was originally going to take two and a half times that when I was thinking about going there and back, and when I thought I could travel the entire length of the river Murray.
That would have been 5000km.
That's why I now have a revised Murray river epic solar powered boat adventure plan.
Both 2000km and 5000km are probably a bit long to be travelling at walking pace unless I can figure out some way to make walking pace a little faster, or perhaps break up the trip into lot's of more manageable chunks.
Making walking pace faster would be pretty easy to accomplish by only going downstream when the river is in flood. As far as I can tell, it flows at around 1-5kph, so starting at the top might be a good idea if I'm only going to travel at walking pace. My little boat runs at around 3kph, and if the river is flowing at 3-5kph, 5000 km backwards might get dull after a while. And 5000km backwards from the Murray mouth is... well... the south pole, and those last few hundred kilometres would be difficult on a boat, what with all those rocks and ice. On the other hand, I don't want to tear along at the un-tranquil pace of as high as 8kph by going downstream.
Perhaps I'll just drift.
That would give me loads of spare amp hours to get up to water skiing pace and blare out music into the tranquillity.
The Murray river has thirteen weirs along the 1986km long stretch from the Yarrawonga Weir, to the Coorong where it meanders into the ocean. As far as I can tell the weir at Yarrawonga is the highest point up the river I can travel by boat. All the weirs along that stretch incorporate locks to allow boats to navigate it's length.
So, my revised plan would probably be to start at the closest boat ramp to the Yarrawonga Weir, then follow the river west, or as I like to call it, left. Then turn left again a thousand kilometres later or so, and continue south until I hit the beach.
Sounds like a plan.
View Murray River National Park in a larger map
Things so far...
Animation (5) Aquaponics (338) Bread (15) Cheese (14) cooking (49) electronics (57) Epic adventurer (20) Escargot (2) Fire (6) Fraudster (1) Handmade fishing lures (31) Home made preserves (11) Making smoked foods (11) Mold making (7) Movie watcher and critic (2) Photography (17) PVC (36) Snail farming (6) Solar hot water (26) Solar photovoltaic panels (7) Stirling Engines (11) Thinking (49) Vermiculture (1) Wind energy (25)
The bell siphon was a clever thing for someone to design, and as such you feel a bit of that "clever" rub off onto you when you m...
You see CHIFT PIST a lot in the aquaponics forums and it means "constant height in fish tank, pump in sump tank". And its a very g...
A "bell siphon" is a device that automates the flooding and draining of an aquaponics grow bed, even though the pump is adding wa...
Painting lures is easier if you don't know how. I don't, so I'm already well on my way. I started by owning a printer. That ...
A while ago I tried to make a fish fed fish feeder design that would allow the fish to feed themselves. I think It's made. I say &q...
Apparently, marron come in two varieties. Hairy and not so hairy. Cherax cainii (smooth) and Cherax tenuimanus, or Margret River marron (hai...
In aquaponics, one issue that can effect your success rate is the pH of your water. pH is a measure of water's (or soil's or whateve...
With a little practice its possible to make a screw. If you bend your wire into an eyelet, its possible to make a screw in eyelet. The use...
I had an idea, but now I'm not sure it was mine after all. But here it is anyway. I need to get solids out of the water for the NFT, ...
This post is a follow up to the " handmade fishing lures how to get most out of your printer " post describing my way to colour ha...